Technical Description from the Manufacturer
The Acousticom 2 is our newest microwave detector. It presents RF measurements as an audio signal, with LEDs and an alarm at high levels of RF (you can also switch the sound off if you prefer to be less obvious when taking readings). With simple controls, easy to read results, but still using the same advanced microwave detector as our Acoustimeter, this instrument is perfect for those on a budget. It is smaller and lighter than the Acoustimeter, and comes in its own carry pouch.
The Acousticom 2 was designed using the experience gained from many years of practical RF and microwave measurements. The advanced RF detector is the same as that used in the Acoustimeter. LED lights display the peak levels of microwave electromagnetic fields from 200 MHz up to over 8000 MHz (8 GHz), covering the frequencies used by most modern communication systems encountered in our everyday environment. This includes TETRA, all mobile phone systems including 4G/LTE, Smart Meters, and all WiFi and WiMax frequencies. The LEDs update rapidly, and allow you to quickly gauge the levels in an area and find any hot-spots. Its readout is sensitive to 0.01 V/m. When two LEDs are both lit next to each other, the exposure level is halfway between the two. This is only for levels above 0.1 V/m, e.g. when both 0.10 and 0.30 V/m are lit, the level is about 0.20 V/m (halfway between).
When first turned on the Acousticom 2 is silent. The sound may be turned on and off by pressing the button. The Acousticom 2 also has an “alarm” sounder which emits a pulsing warning at higher exposure levels. If the alarm is not required, then it is easy to disable it each time when you turn the Acousticom 2 on. The demodulated sounds allow you to determine, with a small amount of practice, what type of device is creating the pulsing microwave levels that are present. These features make the instrument the most useful and practical one available – even for people with severe electrosensitivity.
The Acousticom 2 reacts to very short pulses. Peak readings are what they say – the highest sampled reading – though the sampling and processing rate means that there are some gaps and it will not always react to a SINGLE VERY short pulse(less than about 5 microseconds duration) – though it will react correctly to much shorter pulses that are regularly transmitted (such as from WiFi).
Please note: The internal antenna is at the upper half of the case and the back. Signals are best measured when the source is behind the instrument, but also quite good with the source to one or other side. Turn the Acousticom 2 for the highest reading.
- A line of coloured LEDS displaying Peak exposure levels in V/m
- Measurement range: 200 – 8 000 MHz ±6 dB (typical accuracy)
- Sensitivity (Peak Display): 0.01 – 6.00 volts per metre (V/m)
0.01 0.02 0.05 0.1 0.3 1.0 3.0 6.0 V/m;
(equivalent to 0.5 to 100,000 peak µW/m2)
- Some intermediate points when two LEDs are both lit are also defined: 0.2 0.6 2.0 4.5 V/m
- The speaker may be switched on and off
- An alarm sounder at higher exposure levels (may be disabled)
- Power source: 1x PP3/MN1604 9 volt Alkaline or Rechargeable
- Power draw: 40 to 90 mA (depends on the sound volume)
- Battery life: Up to 10 hours continuous with normal alkaline battery
» Low battery indicator light (the green ‘on’ light turns red)
- Size (mm): 110 x 63 x 21 (LxWxD); Weight: 140g incl. battery
The Acouticom 2 is currently 5G compatible for the UK and rest of the world (excluding USA) as it can measure all of the frequencies that 5G networks plan to use over the next couple of years. In the USA it will be able to measure some of the future technologies but not all. Click on the below link for more details: